Ski-Doo Snowmobiles Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 43 Results
  1. REV-GEN 4 & 5 - Backcountry/ Freeride
    Hoping to use a M8x25 bolt instead of the BRP hex heads for the back plate (inside) of my secondary.. (original ones backed out.. lost one and limped home with hand tight 3 others)
  2. REV-GEN 4 & 5 MXZ Perf. Trail 129/ Renegade 137
    2008 MXZ Renegade X with 5000 mi. Last year just a few hundred miles ago experienced the infamous secondary clutch rollers shattering to pieces. Ordered parts and tools from C & T Powersports based on many recommendations here and repair process went smooth and no noticed issues since. For...
  3. MXZ / Legend / Summit / Grand Touring / Formula
    Just picked up a 2002 Summit 500f for my daughter and also purchased the Shop Manual. Upon cleaning the secondary clutch I noticed that the clutch on this sled isn't what the shop manual calls out. The secondary has a yellow spring that needs to be preloaded. (?) This is a first for me since...
  4. REV Chassis - Mountain Sleds
    Hi, i have a 2006 skidoo summit 800ho 151", 2" paddles and i am heading out west this year with it. I was looking for some clutching advise as far as a good setup for high elevation (6000'+). Currently its stock clutching, but i do have a team tss-98 secondary with a 44str helix i believe laying...
  5. REV-GEN 4 & 5 MXZ Perf. Trail 129/ Renegade 137
    Just thought I would share how I install my secondary without issue. Clean the outer race of the bearing and the bore which it sits in. Use a little grease or anti-seize in the bore. Insert the jack shaft. Pinch the bearing and housing with your thumb and fingers. Squeeze and at the same time...
  6. REV-GEN 4 & 5- Summit/Freeride/ 850 Turbo
    Was looking to see if anyone had any input on the Team Tied on the 850's? How was backshift, heat between the two clutches, what springs and helixes worked better? What did you end up with in the primary. Did a search on every forum out there and didn't find anything... Just wondering what...
  7. REV-GEN 4 & 5- Summit/Freeride/ 850 Turbo
    Can any of you guys tell me what helix comes with the ibackshift clutch kit for the 2018/2019 summit 165 3" with the 965 ramps? Purchased a used kit off a buddy and I dont want to waste time installing if I dont have the right Helix. Kit I got came with the NC-D5 Helix Thanks
  8. REV-GEN 4 & 5 MXZ Perf. Trail 129/ Renegade 137
    so sled all of a sudden seemed real sluggish and bogged down and wouldn't get rpms right off. took a look and the belt was about a inch down instead of right at the top so I removed it and spun out the tool and clutch to not return to position like it should and after some banging it flew out to...
  9. REV-XR/XS Chassis: 4-TEC 1200 Perf. & Trail Models
    I run a pb80 primary and secondary is stock..i'll run down the events..tried loading my sled onto my trailer and it wasn't moving so thought I had issues..turns out my ebrake was on (yeah i'm dumb)..decided to put my dayco xtx belt on that I bought as a spare..I cleaned the belt well with soap...
  10. Vintage Classifieds
    I have an older Ski Doo bushing in my parts stash. I have no idea what model or year sled this fits. Looks like perhaps a secondary clutch bushing. It is Doo part # 405601400. It also has the number 9201 stamped on the outside. Length is ~ 1.722 inch, ~44mm ID is ~1.133, ~29mm. $5.00 +...
  11. Vintage Ski Doo's
    Hi, I acquired the secondary but don't know what model it's from, it's in good shape so I would like to replace the spring and ramps and use it, my problem is I don't know what parts to order because I don't know the model. here are a few part numbers I found on the assembly 414-1009-003 on...
  12. Vintage Ski Doo's
    Anyone know the secondary can degree (angle) ( stock) for a 1980 - 5500 Blizzard ? TIA
  13. Vintage Ski Doo's
    Got Bushings! Yep cheaper by the dozen... Anyone ever do a fix on their secondary clutch shaft? Have a smaller size heavy duty snap ring (1-5/16" shaft size) cut the groove a little deeper but also thinking I'll back it with a washer 1-1/4" fits the 1-3/8" shaft pretty good and a 7/8" behind...
  14. REV Chassis - Performance and Trail Models
    Ok here is the question my primary and secondary sheaves are broken and i have to fix this ASAP. so the question is i have an skidoo rev xrs 800 2007 what kind of primary clutch does it have? i only have to change the sheaves so i will most likely buy used sheaves and move everything inside...
  15. REV Chassis - Performance and Trail Models
    Hi, not sure if this has been addressed before but here goes:: Bought the sled at the beginning of the season and it never went over 80mph. I knew that was strange but never dug into it, figured bad gas or whatever. Now after putting 400 miles on it wont do over 63mph all of a sudden. I...
  16. REV-XP / XM Chassis - Mountain Sleds
    So I put about 400 miles my first year on my Summit. End of season, ran it through the automatic fogging process, put stabil in gas tank (which was basically a full tank), then put it in garage for summer Started it a few (maybe 4) times during summer, always started instantly Winter was...
  17. 900 ACE 4-Stroke Models
    Does any one know, what the secondary spring pressure is, for a 900 ACE. Mine from the factory is set to 25lbs beak away. All of my past sleds where in the 15 to 21lb range.
  18. REV-XP/XS Chassis: Renegades/Freeride/Backcountry
    I have a 40-XT and a 44/42 QRS helix on my shelf and I cant remember where they came from. I'm pretty sure the 40XT is off of a 800 FreeRide and the 44/42 is off of an 800 XRS? Does anyone have a chart or parts listing that shows applications? Thanks
  19. Skandic / Expedition
    I'm hearing there are issues with the ability of the secondary tower to handle the torque of the 800 etec. Has anybody with an XU chassis braced their secondary tower?
  20. REV-XP/XS Chassis: Renegades/Freeride/Backcountry
    Look familiar? I am about to get the wrenches out. Toasted roller? Bad spring? what would you wager?
1-20 of 43 Results
Top