Search Results for ‘rev’

I have a 2005 Rev 600 HO SDI I left it out in the freezing rain no cover for one day I come out to start it in the morning everything was fine started up with the e start after about 2 minutes of letting it warm up the sled shuts off randomly no idle down just shut down the rpm gauge being stuck...

Looking at buying a BMP can for a 600 SDI. Will this still fit on my 2006 mxz 600ho?

Hi everyone! I'm creating stickers for my Ski-doo Summit and I've been looking all over the internet to find a similar font used for the REV chassis stickers, the same ones used for the REV XP/XM/XS. I tried using online font scanners by uploading these screenshots, but no luck so far. Curious...

So I picked up a beat up 440, it sat a long time in the shop while I piled parts to fix it. Finally I got it going. From what I’ve been told it was a ripper, always put gas n go. But I’m finding it was running pretty crappy in the -7c the other day. Takes off after sitting for a bit..but 2 mins...

So I have a 2009 Renegade 137 that I was looking to install studs on due to having no traction on some of the icy trails out my way. I bought the single ply 1.375" studs from FastTrac and went to go install it after installing the tunnel protectors but I noticed on the track that is on it states...

Im trying to figure out how to replace the left hand controls with rocker switches on the dash and I can’t figure out what wires are what

Hey guys I’m having the pcode starter relay short to ground or open circuit. I do not have electric start or the starter relay. I have the small battery with the capacitor. I can’t see any damaged wires and tried changing f4 fuse like it says and I also disconnected the capacitor with no...

18' XRS Pro 40 center R motion rebuilt 0 miles $450 18' XRS Renegade Pro 40 Rear w Quick adjust rebuilt 0 miles $450 09' X front shocks $300/ pair SC-5 120" skid w 1 cheap shock no wheels $125 SC 10-3 rear skid w adrenaline shocks usable $150 Rev summit parts - SC 10 ,misc parts - front arm...

Hello. I have a rev 600 ho sdi 2005 and im thinking about gearing it down. has anyone tried 46 lower gear? dont even know if it fits xD its 22/43 original and i think i will put 19/46. it is pretty slow from a holeshot and i dont need more than 130kmh top speed. im aslo going to extend it from...

Hi! i finally got ahold of a complete 850 engine with complete harness and every sensor. Noe i am putting it in the sled. Where do i start? Have anyone done something like this before? Need som guideance and tips to make it go as smooth as possible.

C&T Power sports Track Tension / Alignment Tool Can ship

Hello all, I'm working on a full rebuild on my 05 summit 800 HO. I'm installing dual ring SPI pistons. I'm to the point of installing my piston rings. The rings have obvious markings indicating the top side. The problem is that one ring says PJ21E, and the other says PJ21F for both ring kits...

Hello, I recently finished rebuilding my 2003 ski doo rev 800 sport (non ho). It has a brand new crank, piston, rings, check valves, clean carbs, seals and lines. Unfortunately it won't run correctly. It cuts out above intermittently above 1/2 throttle. It idles fine though. Has 140...

Recently bought an 04 600 with only 600 miles on it, runs great however after another 6-700 miles it stalls when put in reverse,I added electric start with the bigger battery etc. and still does the same !! any ideas?

So I have a 2004 Summit 800 HO 144 that’s not in the best shape. The motor itself is great, starts right up and runs the way it should. Only problem is that the rest of the sled is pretty bad, especially the track. Almost all the lugs are ripped and torn, and the thing gets stuck constantly in...

I bought a 2003 800 sport (non ho) in the fall with a bent connecting rod. I rebuilt the engine top to bottom with all new parts. Now I have it all back together and took it for a spin today. I can't get it to go above 25mph now. Unfortunately the tach doesn't work so I'm unsure of the ram. It...

Hey Everyone, I recently just bought a 2004 Skidoo GSX 600 H.0 SDI with no motor. I do however have everything from the throttle bodies, injectors, exhaust ext. I am not overly familiar with the fuel injection machines because I’ve always run carb machines. I have a couple questions regarding...

howdy folks! figured id better ask the professionals. recently acquired a 2004 rev mxz x 800ho! sled reaches 80kms per hour max.... reving at 8000rpm gearing is 22/43 10t drivers primary was really neglected, cleaned and ordered a rebuild kit.... sled has 120psi on both cylinders...

what would cause this to happen to the connecting rod? Took sled out for a ditch rip just doing mad wheelies and it seized up… 2012 600rs

Hey everyone. I'm wondering if the 151x16 track from a REV (pitch 2.52) is a direct fit on my 03 Zx summit with a 151x15 track or if there's some other little things to do? I'm trying get some more flotation out it and I've already bought fat skis to help with the plowing. And...