Search Results for ‘rer’

Just picked up a 2002 Summit 500f for my daughter and also purchased the Shop Manual. Upon cleaning the secondary clutch I noticed that the clutch on this sled isn't what the shop manual calls out. The secondary has a yellow spring that needs to be preloaded. (?) This is a first for me since...

Is there a certain temperature required (for the machine/engine to warm up to) before reverse works? I was out riding and went to reverse and no go. This was the first time I have ever used the reverse on this new machine, a 2021 Expedition SE 900 ACE. After I pressed the button to go into...

Hey guys, I purchased a rev 500ss last year and the rer is not functioning. When I press the button, the sled stays idling and the rpm does not change. I am unsure which wires are used for the rer system and have traced a few that were unplugged and was wondering if they had anything to do with...

Hi guys, new to the forum here. Thanks in advance for any thought or advise regarding my issue. I have a 2012 mxz x 800r etec. 1500 miles. The piston recall was done around 1000 miles if I remember correctly. Anyway, Just recently after pulling my sled out of storage for this season, I...

Hi everyone. I am in the process of building a 2002 Summit highmark 800 with a 2003 HO motor and converting it all to RER. I have the spark working and the motor is at 155/158 psi. My question is, the intake boots are all cracked to hell and probably leak. they are Vforce3 reed cages and have...

Hey Guys, I have just finished a rebuild on 800r. New pistons, good cylinders, used crank within spec. It fires first pull everytime, and is running great however it will not fire in reverse. It just dies when you press the rer button. Compression is even at 132psi each side, idle set at 1800...

Hi folks, I've encountered a very frustrating issue, and of course it has reared its ugly head the friday of the free trail pass weekend in quebec. The sled is a 2015 600 etec renegade X. With the key plugged in, when I pull the kill switch up the sled starts up without touching the start/rer...

Hello. Finally i got rebuild the engine, but i cant figure out the ignition and the triggers. The snowmobile is Mach Z R 99, it got RER. I am using a dial gauge on mag cyl, but there is no nub spot on the stock ign (2.59mm BTDC) and there is also no nub around some other logic timings. I...

I've done some searching on the site but haven't had any luck finding an answer. And if I'm posting in the wrong forum, please let me know! :) Looking at an '07 800 Summit X 151". Fresh motor, BOSS seat, looks like it's in good shape. And no reverse. I have never worked on this style of...

I am struggling to find the fix of my speedo issues on my 05 MXZ 600HO non SDI. Its not just the speedo. I the past when the speedo jumped to 135 mph it was a sign to change out the relay. Always had success.This time not so. I have tried 2 new relays and the problem persist. Hand warmers are...

Hey guys I have a 2010 xp and I have rsi back country bend bars and with the brake and rer block on the same side there's not much room for my hand due to the dimmer switch sticks in my thumb any advice what to do or can I relocate it also I have the rsi risers ?? Thanks

I had a incedent this winter and broke the shives on my secondary (06 500ss) I came across a non rer secondary can I change the helix and what not out and make this an RER what are the differences between an RER and non RER the secondary I got came off an (03 600 HO) thanks in advance for any input

i got a 2003 rev x 800, the tach isnt showing RPM and i have checked everything! changed the relay, and even tried the following, MPEM, coil and tach and speedo. ive checked the whole harness from top to bottom. ive even check the stator and it is producing power correctly, but the service...

would bad or misaligned pickups cause my tach to not work? that is the only thing i have left that could be wrong with the sled and would like to be fairly sure before i pull the motor again... I just got it all together so it may have been mis installation by me but it was my first rev motor so...

hi all, I have a 99 ski doo gt 700 triple with rer.. just rebuilt by a professional new crank new pistons bearings seals the whole works... got it running today runs great and smooth for 10-15 minutes stop to let it idle it dies... now go to turn it over it and it kicks over but then the rer...

Item: WTB RER Setup for 2002 Ski-Doo MXZ 500 L Category: Sled Year: 2002 Location: WI Price: Let Me Know Hi all, I'm looking to buy all the parts I need to install RER in my Non RER 2002 Ski-Doo MXZ 500 Trail LC sled (ZX Chassis). Below is what I need HPV27 Secondary from RER sled Flywheel...

I just installed a fresh BJ rebuilt 800R motor on a new to me 07 summit Adrenaline. After talking with BJ I decided to remove the electric starter, ring gear, battery, and wiring to save weight. I started engine for the first time tonight. I push the RER button and there is no Reverse, it...

i recently bought a complete electrical system from a 02 mxz 800 with rer (mainly because my 600 doesnt have rer) and i need to get the mpem tuned. i was wondering if there would be some contact info on a person who can tune mpems

i just bought a whole electrical system of a 2002 mxz x 800 with rer, i have to put that into a 600 summit. and i was wondering where i have to send the 800 mpem to get programmed if i have to. and if the mpem doesnt have dpm is it possible to get dpm programmed into it? because my 600 has dpm

im looking for a mpem with rer, but im also wondering what other parts do i need to put electric reverse on a non rer sled :shrug