Ski-Doo Snowmobiles Forum banner
primary clutch
1-20 of 22 Results
  1. Vintage Ski Doo's
    My 1974 300SM primary clutch is sticking. Removed outer half and square shaft is worn on leading edge on all four sides. Brass sleeves in the bore were badly worn so I replaced with new ones. Sprayed graphite on the shaft before Assy but still seems to be sticking without belt. New sleeves...
  2. Vintage Ski Doo's
    I bought an '89 Citation in September from a local seller that had it for his grandchildren. When I was looking it over with the guy he mentioned that it had electric start but it didn't work, saying there was something missing 'down there' as he pointed to the clutch side. He mentioned that his...
  3. Sled Parts For Sale or Trade
    Item: Cudney 900 Ace Clutch Kit w/Extras Category: Sled Year: 2014-2019 Location: Owosso Price: $650.00 SOLD! Cudney Racing Clutch Kit: PB80 Primary Clutch with correct spring and weights installed, Helix, Secondary Compression Spring, correct length clutch bolt, Primary Clutch Holding Tool &...
  4. REV-GEN 4: 850 MXZ Perf. Trail 129/ Renegade 137
    Lake Running 2019 850 Primary Clutch Explodes
  5. Vintage Classifieds
    I have an older Ski Doo bushing in my parts stash. I have no idea what model or year sled this fits. Looks like perhaps a secondary clutch bushing. It is Doo part # 405601400. It also has the number 9201 stamped on the outside. Length is ~ 1.722 inch, ~44mm ID is ~1.133, ~29mm. $5.00 +...
  6. REV-XP / XM Chassis - Mountain Sleds
    I have a 2013 skidoo summit xm 800. When I start it, the sled starts to crawl, I have to put hard on the brake in order for it to stay put. I have replaced everything.... bushings, spring, also I did a full rebuild with rollers and pins last year but didnt swap out the ramps.... I dont know what...
  7. Sledding - General Discussion
    Need some advice as to if this can be fixed. All 3 allen head bolts that hold the spring cap down sheared off, do I need a new clutch or if possible get the remaining portions of the bolt out and get new bolts? Doesn't seem to be any other damage. Has anyone ever seen this before?
  8. REV Chassis - Performance and Trail Models
    I have been reading a lot of old threads, but am looking for some fresh opinions. Anyone with a 2004 500ss have any suggestions for clutch kits. Rebuild kits? I'm looking for an all around good kit (I know you can't have the best of both worlds, but something close). I'm bored 20 over, v force...
  9. REV Chassis - Performance and Trail Models
    Pulled my primary clutch off tonight to look through it because it was wobbling a bit. When I opened it up there were broken parts and it had started eating itself alive. I thought about rebuilding it but it looks to be cheaper to buy a new used one. I am going to mainly be riding at elevations...
  10. REV-XP/XS Chassis: Perf. Trail 120-129 Inch Models
    i have a new 2016 xrs with out the electric starter, but they installed the ring gear on the clutch. are the primary clutches balanced with the ring gear on them? did anyone have any problems with removing the gear? thanks
  11. REV-XP/XS Chassis: Perf. Trail 120-129 Inch Models
    I just bought an 11 XRS and the primary is vibrating bad. Every other Ski-Doo I have seen has an arrow on the outer most sheave that line up with an arrow on the next sheave...but mine does not. Any input on how to tell if it is assembled improperly?
  12. REV-XP/XS Chassis: Perf. Trail 120-129 Inch Models
    Anyone have the specs for the spring cup bushing and the other bushing on the sliding half 800 2012
  13. Vintage Ski Doo's
    Ok so I'm new to dootalk but I've been working on my skidoo and I was driving it earlier this year but the primary clutch is stuck in the closed position and I believe I need to get it off to replace the inner parts. My issue is I can't get the clutch off. First of all the first flange spins...
  14. MXZX Race Sleds
    Okay so bought a new inner sheave and a new guide coupler. Got everything back together on the sled. Looks to me that a low idle it wobbles more than it should. Wobbles more than my old worn out Indy 500. I have a new bolt and washer in it as well. Also everything is assembeled as it should. Any...
  15. REV-XP / XM Chassis - Mountain Sleds
    '09 Summit Rev XP Anniversary Edition, 800r engine (For some strange reason after signing in, there's no search window in DooTalk tonight, so I'm going to ask:) I'm you-tubing up on the water trick, but I have an OEM shop puller for the primary (drive) clutch which is stock, but that puppy was...
  16. Race Sled Classifieds
    2003 mxz light weight primary clutch. good shape. $150 plus shipping.
  17. Sledding - General Discussion
    Can anybody tell me if a primary clutch from an 07 600 HO will be the same as the primary on an 08 800R? I need some parts for the 08 and have found some for sale. Just wondering if it will work.
  18. REV-XP/XS Chassis: Perf. Trail 120-129 Inch Models
    So I took my primary clutch apart again because I broke a clicker bolt trying to adjust it. While I had it apart I scrubbed her down and gave it a good scuffing with a scotch bright pad to get the residue off the faces from my new 391 belt i put on 500 miles ago. Here are some pictures of the...
  19. Vintage Classifieds
    Hello All: I have for sale various Vintage Bombardier Ski-doo parts, including a 299 Single cyl Rotax engine complete with Clutch and Muffler. No Carb or starter recoil. A 247 Elan Head, Cylinder and Crank. Crank,Cylinder and Head are in excellent condition. I have Front Light Assys...
  20. Wanted To Buy
    The splines on my fixed sheave are creacked, does anyone have one for my 2006 summit 800? I would conside a complete primary clutch if the price is right. Please give me a call. Roger 801-550-8438. thanks in advance!
1-20 of 22 Results
Top