Search Results for ‘mod’

Where can I buy a dash block off plate like this??

Hey guys! Had a little too much fun in WNY last week with my 13 pro open mod chassis 600rs. Melted down the PTO side after a WOT pull across a field. Too cold to tear down yet but, Obviously when your junk blows up you add more power... because that solves everything. Questions- 770 DMAX vs...

I know theres been similar subjects in the past but parts are harder to find today. Just got a Legend 700 GS 2002 and I want to do a couple mods to lighten the front and make the ride a bit more comfortable. Here is what I'm thinking... I'm looking for advice, where to find parts (if you have...

Picked up an 06 summit 800 151 in trade, figured it would put me back in about where I left off with my 05 roughly ten years ago. The sled has about 3600 km on it and from what I read the outside main bearings need isoflex about this time. Figured out pretty well how to repack the pto...

Hello gentleman, I have a question on what my sled would be worth. Last year I picked up a 2004 MXZX 440 with a 800ho swap. Very nicely done. It was a older mans "local" riding sled. The sled has 2500 miles on it. I am thinking about getting rid of it and wondered your opinions on its worth...

What is the best modification for a bone stock MXZ 600 in your guys minds (without spending the retirement fund). LOL.

I have a 09 600RS and am picking up a 2011 xrs 800 etec to do a complete engine swap on the RS. open to any advice warnings or cautions anyone may have or any general input on the project as it will be a first and there is not much info on a etec swap, more on the Ptec! any clutching suggestions...

I am thinking of upgrading the exhaust on my sled, getting a better can. the problem is that on my S Chassis my pipe and can are one piece. So if I wanted to get a new can I would have to get a new pipe that would fit my sled, as well as a can. I did some research and found someone with the same...

I have a 1997 Formula 500 and I would like to have a taller stance on it as most older sleds are really low to the ground. I did some research and found some stuff on getting shorter radius rods, but I don't fully understand and I am looking for some help.

Hi guys, Just wondering if anyone has tried fitting XM side panels up to an XP? Only curious because I really like the idea of the narrow skinz helium panels, think they'd look tough on my sled..

So I seized my mod on Saturday, its an 07 mod kit thats essentially stock except for custom domes @ 14.5 for av gas (dominator 32:1) and a mystical trail mod timing curve from Tom Lawrence that I have no specs on. ( side note, anyone know what it takes to reprogram these race ecm's? Somebody has...

Over the summer i installed a C3 belt drive into my 07 Rev. I was not able to ride it until last week at which point i started having issues. I have went through 2 belts in 5 rides. The belts look like they are catching on the tensioner lip and slowly being chewed up. It is definitely an...

Hi, Just wondering if anyone has Bigworms contact info. I sent him a message and he hasn't responded, anyone know another way to contact him? Thanks!

Hey guys! Time to go active here on DooTalk since I'm starting a mod project on my mxz 600 -01. This site is awesome for inspiration and help and hopefully I can give some inspiration too and get some help and tips from you awesome people out there when I mess up! I'm new to writing on this...

Hey guys, I've got a 02 mxz 700, bought a 151 skid from a high mark and I'm looking for the ctc distance of the two mounting holes, I've looked everywhere online and I can't find anybody who has posted it, any info would be great!

hey guys, so ive started a project on my 02 mxz 700, i bought a 151 track and a 02 summit highmark skid, 151. i cant find anywhere of the ski location measurements, anybody have a 02 summit high mark? could you please tell me the distance between the two mounting holes? any help would be greatly...

Hi guys, I have a 2008 summit 800r with a few things done to it: Trygstad porting, Trygstad head, Trygstad ceramic coated pistons, Vforce reeds, Timbersled intake, SLP y pipe, and J&T can. It was rebuilt this summer to Dave's specs as I previously had a smaller base gasket and slp pipe and...

Taking a 06 mxz 500ss and making into a mountain mod sled I've just purchased the track and the 162 skid. The track is a 2.52 pitch so I'm looking to find some new or used extrovert drivers. I'm not too sure how to measure the width (Bore) of my driveshaft though! Also...the extros on Royal...

Finally got started on my mod sled. I bought the citation last year, which has a 250 in it and this spring I bought a junky Yamaha srv 540, the only good thing on it was the motor. Im going to drop the srv motor in it. Should rip pretty good. Then I bought a 121x1" track and suspension, and duel...

Hey guys Im wondering if anyone knows if the width or general size of the 129 race sled rear heat exchanger is close to the 08 pteks mxx ? im looking to mount it in a 08 mxz tunnel and using the rs end cap to extend the stock 120 tunnel to the 129. It all seems far fetched but the orignal heat...