Ski-Doo Snowmobiles Forum banner
flywheel
1-13 of 13 Results
  1. Sled Parts For Sale or Trade
    Is there anyone that has any intel to getting a flywheel (part #42066040)? It is discontinued and I have searched many dealers with no luck. Is it possible to resurface teh part and re-use? Any help appreciated. Thanks
  2. Sled Parts For Sale or Trade
    Item: Flywheel Puller & Installer Ski Doo 600 Category: Sled Year: 2007 Location: Owosso Price: $25.00 Flywheel Puller & Installer Ski Doo 600 SDI HO and others. Use it to remove and install flywheels. Required when lubing flywheel side crank bearings. Was purchased from C&T Tools. Asking...
  3. Vintage Ski Doo's
    Can anyone here help my diagnose a faulty stator? Mine seems to check out fine when tested with an OHM meter on the generator side but wont produce any light thru the lighting coil. Does the lighting coil have anything to do with igniting the generator? I had the sled running several times...
  4. REV-XP/XS Chassis: Renegades/Freeride/Backcountry
    Changed out my stator on 09 etec gade. Having issues with flywheel nut and spacer? Can't seem to get enough room on the shaft to put both back on? Should I tighten nut on first and set flywheel and then take nut back off and add loctite and at that point spacer should be able to go on?
  5. Vintage Ski Doo's
    Hello, I have a failed PTO seal on my 503. Today when I was pulling it appart I noticed the flywheel has to keyways cut in it. Is this standard or has someone done a mod ? Thanks & Take Care Roy
  6. Mach Z / Mach 1 / Formula III Triples Classifieds
    Since it seems the Mach Z RT's don't have their own classified section, I'll leave this here Have a host of good Mach Z/Summit Highmark/MXZ Renegade 1000 engine parts from a 2006 1000 SDI for sale Good set of matching upper and lower 1000 SDI cases (no cracks or welding), comes with both oil...
  7. Sled Parts For Sale or Trade
    Item: Misc Mach Z 1000 engine parts Category: Sled Year: 2005-2007 Location: Sudbury, Ontario Price: $600 Have a host of good Mach Z/Summit Highmark/MXZ Renegade 1000 engine parts from a 2006 1000 SDI for sale Good set of matching upper and lower 1000 SDI cases (no cracks or welding), comes...
  8. MXZ / Legend / Summit / Grand Touring / Formula
    Looking for a flywheel for a 2003 Legend 380F. Part # 420889376. The sled is barely worth the price of a new one.
  9. Vintage Ski Doo's
    I have a 277(72mm x 66mm) Single that had a Bosch Points Ignition. I want CDI, so what is my Options? My 277 Crank Mag End Taper is 23.65mm (0.931") on the Big End, 20.96mm (0.825") on the Small End, 23.59mm (0.928") Long. The Bigger Mag End Taper on say a 377 - 617 is: 27.8mm (1.101") on the...
  10. Sledding - General Discussion
    The magnets on fly wheel on my 2006 600 sdi cracked and i was wondering where i can find a used or salvaged (one magnet) flywheel not for the $412 dreaded dealership price!
  11. REV Chassis - Performance and Trail Models
    I am doing a full rebuild on my 07 800ho Ptek and when I was pulling the "flywheel" (Item #3) I was using the other flywheel ( Item #7) with some barstock as a puller to break the taper lock on the crack shaft and get Flywheel #3 off. Problem is I slightly bent Flywheel #7. I can machine a new...
  12. Wanted To Buy
    Item: WTB RER Setup for 2002 Ski-Doo MXZ 500 L Category: Sled Year: 2002 Location: WI Price: Let Me Know Hi all, I'm looking to buy all the parts I need to install RER in my Non RER 2002 Ski-Doo MXZ 500 Trail LC sled (ZX Chassis). Below is what I need HPV27 Secondary from RER sled Flywheel...
  13. REV-XP/XS Chassis: Perf. Trail 120-129 Inch Models
    I have been searching for a day now trying to get this straight. when I change to a newer 800R do I just need the new flywheel or do I need the stator and pick ups as well. Thanks
1-13 of 13 Results
Top