Ski-Doo Snowmobiles Forum banner
cylinder
1-20 of 42 Results
  1. MXZ / Legend / Summit / Grand Touring / Formula
    Just blew up my 97 MXZ 670. I have three 670 motors to take cylinders from. The two best cylinders are stamped with a "2". All three sets of cylinders came with a cylinder stamped with a "1" and a "2" Cylinder. I looked them up, and all 6 cylinders have the same part numbers. Is there a...
  2. REV-XP/XS Chassis: Perf. Trail 120-129 Inch Models
    Hello All - First time poster, long time reader. I recently acquired a 2015 MXZ 600 H.O. ETEC TNT which was in great condition has around 3900 miles on it. On my first real outing on a lake with a combo of hard pack and fresh snow riding, the sled started exhibiting this weird bogging-down /...
  3. MXZ / Legend / Summit / Grand Touring / Formula
    Please let me start by saying if this has already been posted or discussed before I apologize, as I am doing this from my phone and hard to navigate. However I have a 2003 summit 550f zx chassis . I only have 90 psi on each cylinder and its been that way for 3 yrs. I know its low and too low. I...
  4. Sled Parts For Sale or Trade
    Item: 800 Etec top end for sale Category: Sled Year: N/A Location: Canada Price: $950 Brand new cylinder with a set of dual ring ProX pistons and a gasket set, includes everything in photo, $950 US shipped within North America. Fits all 800 Etec and will work on Ptek models as well
  5. Sled Parts For Sale or Trade
    Item: 800 engine parts Category: Sled Year: N/A Location: Mehoopany Pa. Price: $25 and up All removed from 04 800ho Rack carbs - $75 Cylinder with piston - $100 Rage cage with reeds - $50 Exhaust valves - $40 Cylinder head - $75 Oil pump - $25 Water pump - $25 Stator flywheel and pickups -...
  6. Sledding - General Discussion
    Hi Folks, I'm looking for suggestions on places to go to get a pair of cylinder bored locally (Ottawa/Ottawa Valley). Theyre actually from a seadoo and the new sleeved that I put into them need to be bored slightly to their final diameter and need to be honed. Currently they still have some...
  7. Sled Parts For Sale or Trade
    Item: Team tied clutch, Rev and XM Parts F/S Category: Sled Year: N/A Location: Northwest Iowa Price: 5 Got quite a few parts leftover from previous sleds. If you think I'm too high shoot me an offer on messenger or text 307-677-5230. All prices are plus shipping. Pictures of most everything...
  8. Sled Parts For Sale or Trade
    Item: 880R Crank Shop Trail Motor Category: Sled Year: 2008 Location: NC Price: 2100.00 plus shipping 880R Crank Shop Trail Motor. Motor has approx. 1900 miles and came from my personal sled part out. There is absolutely nothing wrong with this motor, bolt it in, start it and go. This is a mild...
  9. REV-XP/XS Chassis: Perf. Trail 120-129 Inch Models
    So my question to all of you engine guys out there is.... when should I replace my rings and pistons on an etec engine? I'm about to buy an 09 MZX 600 H.O. etec with 5100 mikes on it and I had some guys at work asking me when am I going to replace the rings and pistons. This machine runs great...
  10. MXZ / Legend / Summit / Grand Touring / Formula
    Would someone be kind enough to send me the service manual pages in pdf for 1999 mxz 670 ho piston ring job?
  11. MXZ / Legend / Summit / Grand Touring / Formula
    I am looking for help identifying replacement cylinders for my son's 01 MXZ 600. The cylinders on it has a casting number on the side of 6923 434. I bought a replacement cylinder that I believe came of a 2002 MXZ 600 but it has a casting number of 6923 432. The obvious difference between the...
  12. MXZ / Legend / Summit / Grand Touring / Formula
    So, my exhaust gaskets were shot. I decided to pull the manifold and all but one bolt came out - it snapped off. In addition to the snapped off bolt, the y-pipe also had a crack. Y-pipe fix: - cleaned it up - screwed to a piece of 4x4 - welded - let cool over night still attached to the...
  13. REV Chassis - Performance and Trail Models
    Sled has 2,600 miles, compression is good @140, but there looks to be some scuffing going on in the process cylinder, this is my first rev chassis, and I'm not a fan of the intake system, thinking the scuffing is from snow and belt debris ingestion. Also it looks as though the piston crown is...
  14. REV Chassis - Performance and Trail Models
    I have a 2005 mxz 500ss and the clutch side cylinder is having a major build up of oil. Compression is good, spark is good, mag side cylinder runs fine. oil consumption has noticeably increased. the oil will build up until the plug will oil foul and causes the machine to put off excess smoke...
  15. Sledding - General Discussion
    Does anyone know what the Skidoo 470, and the 521, 583, 617, 670, Cylinder Bolt Patterns are? Also looking for Seadoo 580/587, 650/657, 718/720 Cylinder Bolt Patterns. The 470 use's a Head (6) Bolt Pattern based on a 94mm Bolt Circle. The 521-670 use's a (6) Bolt Pattern based on a 100mm Bolt...
  16. Mach Z / Mach 1 / Formula III Triples Classifieds
    Since it seems the Mach Z RT's don't have their own classified section, I'll leave this here Have a host of good Mach Z/Summit Highmark/MXZ Renegade 1000 engine parts from a 2006 1000 SDI for sale Good set of matching upper and lower 1000 SDI cases (no cracks or welding), comes with both oil...
  17. Sled Parts For Sale or Trade
    Item: Misc Mach Z 1000 engine parts Category: Sled Year: 2005-2007 Location: Sudbury, Ontario Price: $600 Have a host of good Mach Z/Summit Highmark/MXZ Renegade 1000 engine parts from a 2006 1000 SDI for sale Good set of matching upper and lower 1000 SDI cases (no cracks or welding), comes...
  18. Sled Parts For Sale or Trade
    Random sled parts that I just want to get rid of....no reasonable offer will be refused!!! Buyer pays shipping in the lower U.S. only!!!! *all parts are from rev chassis* -1 x 800 ho ported cylinder in good shape, no scratches or gouges cast number 613852 $200 now 175 -1 x 800 ho...
  19. Wanted To Buy
    Looking for 98 Mach Z Cylinder - Can be hurt
  20. REV-XP / XM Chassis - Mountain Sleds
    Pulled the Y-Pipe off my 09 Summit 800R and took a look at the pistons. MAG side looked real good but PTO side not so much. How bad is this? MAG: PTO: Looks like there could be some carbon/sludge there that I should've tried to wipe off, or is this somewhat typical? Thanks for the...
1-20 of 42 Results
Top