Ski-Doo Snowmobiles Forum banner
crankcase
1-14 of 14 Results
  1. MXZX Race Sleds
    I'm rebuilding my 2015 600 RS and had a couple questions for anyone that has thrown one of these back together. Wondering if anyone has the torque specs for the head bolts, cylinder bolts, and crankcase bolts as well as the tightening sequence for each. I have the sequence for the head just not...
  2. Skandic / Expedition
    I've been chasing a single cylinder idling problem on my 2003 Skandic SUV for several weeks now. Everything ! has been torn down, cleaned and subsequently swapped to the other side and still the problem persists on the mag side cylinder. I gave it one last tear down tonight to try and find my...
  3. Mach Z / Mach 1 / Formula III Triples Classifieds
    Since it seems the Mach Z RT's don't have their own classified section, I'll leave this here Have a host of good Mach Z/Summit Highmark/MXZ Renegade 1000 engine parts from a 2006 1000 SDI for sale Good set of matching upper and lower 1000 SDI cases (no cracks or welding), comes with both oil...
  4. Sled Parts For Sale or Trade
    Item: Misc Mach Z 1000 engine parts Category: Sled Year: 2005-2007 Location: Sudbury, Ontario Price: $600 Have a host of good Mach Z/Summit Highmark/MXZ Renegade 1000 engine parts from a 2006 1000 SDI for sale Good set of matching upper and lower 1000 SDI cases (no cracks or welding), comes...
  5. Mach Z RT and MXZ 1000 SDI Models
    This thread is simply to open dialog about the 1000's problematic crank and crankcase... 1) In your opinion could Doo have made a better design? If yes how? 2) What are the shortcomings or their design? 3) Do you think the liquid cooled case was necessary? 4) Do you think an oil bath crank...
  6. MXZ / Legend / Summit / Grand Touring / Formula
    any good articles on rebuilding an 800 from 2002? mods etc?
  7. Mach Z RT and MXZ 1000 SDI Models
    So I spent 3 months researching, buying parts, and completely rebuilding my '05 1000 SDI engine. I got it all back together, ran it for about 1/2 hour (2 15 minute runs for heat-cycling). I decided to pull the head today, to look and make sure the cylinders weren't getting scored or anything...
  8. REV Chassis - Performance and Trail Models
    Engine blew last week at ~3800 miles and I need some part numbers for the rebuild :sad_old: -piston w/rings (what brand do you recommend?) -gasket kit -size 20 pilot jets -370 mains -starter Also, how do you get the crankcase open? I have all of the bolts out, but I can't get the top and...
  9. General Discussion
    I have lost the pictures I took of the tubes and connections. Now the snow is coming and I have not one clue where some of the tubes go. I got the main one to the injector, the tube that feeds the pump, but there is a tube that goes ta a modual bolted under the carbs, There are what looks like...
  10. General Discussion
    I am reinstalling my crankcase, :boxing: the picture I had are gone. I forgot where they all go. I got the main line to the injector, I hooked up the vent line, but I cant Figure out the rest. There is a line coming from the coolant bottle, all of the other ones. Any advice/tips/pictures...
  11. REV Chassis - Performance and Trail Models
    So I blew my 07 800Ptek up last ride of the year. Just getting around to rebuilding it now. I figured I melted down a piston. I took the head and juggs off found I melted down the Mag side piston pretty bad. When I took the jug off I notice the entire Mag side of the bottom end was full of oil...
  12. REV Chassis - Performance and Trail Models
    2007 blizzard 800 need to replace pto crank seal but can not get cover plate off"! Loctite? Do I need heat? Any suggestion? It is a 4mm hex head correct?
  13. REV Chassis - Mountain Sleds
    So I may have moved to the desert but my love of snowmobiling never died. I think its been a few years since I built my last project which was a fully custom 440 Rev, which I had planned to turn into an 800, but I ended up moving to Orlando and now Phoenix for work...
  14. REV Chassis - Performance and Trail Models
    Hello, Just wondering if any of you know the trick to removing the pickups from a crankcase? Do you heat the "black silicone"? or slice it off? What do i use to re-install on new short block? Btw - I noticed other posters with 2007 500ss crank bearing issues. This sled has only 1800 miles and...
1-14 of 14 Results
Top