Search Results for ‘carb’

I got this sled used just about a week ago, and it drives fine, starts in about 5 ish pulls. The gas has been sitting since march, but did have fuel stabilizer. When I start it up, it will idle decently with the choke, but when I flip it off, it goes to about 1000-1200 rpms, and will shut off if...

It's my dad's sled. 1996 with only 1400 miles! Well since this summer I picked up a Rev Xp it motivated him to want to ride more! But this sled needs a tune up! So I was wondering if anyone had a good jetting setup with this sled that helped it run optimal? It seems a little doggish right...

I want to take off the carbs and clean them but I'm not familiar with carbs AT ALL! I've always had someone else do it lol. Now I want to do it myself! Any advice is appreciated! Thanks

Item: 2013 Ski Doo Summit 600 Sport Category: Sled Year: 2013 Location: Richmond, MN Price: 6,000 2013 Summit 600 Sport(carb) 1,800 miles. rode in the U.P. of Michigan. selling for $6,000, well maintained sled. just need to sell it to upgrade to a new one. PM if interested

Item: 2013 Ski Doo Summit 600 Sport Category: Sled Year: 2013 Location: Richmond MN Price: 6,000 2013 Summit 600 Sport(carb) 1,800 miles. rode in the U.P. of Michigan. selling for $6,000, well maintained sled. just need to sell it to upgrade to a new one. PM if interested

Ok I'm 16 so I have minimal experience and recently took a 97 Formula Z 583 (body and track was totalled after I crashed it) and a 98 MXZ (with a blown engine) but mint track and chassis. So I dropped the engine, clutching, oil/coolant jugs and jackshaft from the formula to the MXZ, the only...

Hi, I'm new to this site, skidoo repair and skidoos in general. I have a 1994 Tundra 2 277 single that refuses to idle. I have cleaned the carb throughly, changed the pilot jet, needle and seat & spark plug. The airscrew and idle screw are set to factory settings to start then bring idle up with...

I want to know if the silencers for the 2013 summit 800 are compatible with my 2013 summit 600 carb? I want to get something louder than stock since i dont ride trails to much, any help on what i should get would be much appreciated!

I want to make sure my carbs are set right. I am adjusting the air screw while it is still on the sled. Do I turn it all the way in "lightly" and then back it out?

I recently bought a 1977 ski doo Olympique in very good condition. The snowmobile has recently been giving me an issue and seems to be only running on one cylinder. I thought it might have been the coil so i switched the 2 coils and the cylinder still runs the same. both sides have spark when...

hi there. i was changing my carb boots and ended up breaking off a bolt. the bolt was sticking out a 1/4 inch or so and by the time i was done [heating,vice grips,etc] i had it flush. anyway drilled a small hole in the bolt and my son stuck an easy out in there and tore a chunk of it off.so...

ok people im about at my wits end I posted a wile ago with some questions about my snowmobile having just bought it I was trying to figure out what it was how to get it running at top and what not , well a few days after I got it it started to run funny it would run but nowere near full...

I need to know what type of carb is in a 1992 ski doo MX xtc r dual carb all I know its a mikuni but nothing else soo help would be great

hey ive got a 2010 summit 600 xp just looking into putting some mods into it ive purchased v force 3 reeds and going to put them in soon as well as a cold air intake also I would like to put in oversized carbs but im having a hard time finding specs of how big I can go. also my secondary clutch...

Hey everyone, I'm pretty new to the new age snowmobiles, I've had my 71 ski doo TNT 440 for almost 10 years and now finally had the money to upgrade and bought a 2013 summit sport 146 600 carb. I just wanted to know how other people think about how the sled performes, especially in the...

Does anyone know what drill bit size to use for a gauge to adjust the slides in fractions. Manual says 2mm, what does that equal, 5/64th? 2001 sled was an 1/8th drill bit, i think the power-tek is different

I am heading to Fernie,BC at Christmas and I am curious as to if I should rejet the wifes sled. It is a 09 500ss mxz that I stretched to a 137"x1.75" paddle track, regeared to 21/45, and added a Cudney Racing clutch kit (new primary and secondary spring, new helix)with adjustable primary...

I just bought an 03 MXZ 500 for my son and it had a problem idling down. It would idle up, but if you quickly tapped the throttle it will sometimes idle back down and sometimes now. It seemed mechanical like a slide was sticking. It had been sitting of coarse over the summer so I pulled the...

I have a 99 ski doo mxz 600 that had a bad crank seal. the motor ran fine just over heated. so i pulled the motor and bought a 02 ski doo mxz 500 motor from a burnt sled and put that in. It runs but it will only run with the choke on a little. otherwise it dies. so i put different carbs on and...

Bought a 1991 Formula MX that had an engine transplant previous owner could not get running. Engine installed appears to be a series 536 1992 Formula Plus as it has the 34MM carbs on her. To make sure previous owner installed carbs in correct location I ask for help... I looked for the 'Red...