Search Results for ‘2010’

i have purchased a 2010 800r Everest and was told it was going to blow up because it is a ptek. i told them otherwise because “they had time to fix the bugs by 2010. i want to know if i was right by saying that. i also came to ask what the difference between the regular 800r and the 800r everest is.

Oops

Looking at a 2010 xrs 800 Ptek.. Are the engines really all that bad if you keep on top of maintenance? I’ve heard ptek aren’t good but are they that bad? I know etec is better just a good deal Also how is the fuel and oil consumption thanks

what is the best route to get a heated grip setup on a 2010 rs?

The head/tail lights and speedometer quit working on my '10 550F Tundra LT. I checked all the bulbs, dried (they weren't wet) and greased the headlights with dielectric grease. I didn't with the taillight. All bulbs looked fine when I looked them over. Dried and greased the speedometers...

when it comes to 2008+ Skidoo xp parts are most or all parts interchangeable between years? I recently bought a lower aarm and it has a turning stop block on it, and now the right side that was already on the sled, does not have a turning stop block. The lower aarms are out 7/8 of an inch. So...

Hello, I have a 2010 summit and the rivets attaching the front rad keep popping off after only one ride out. anyone have this problem and/or a solution?

my 2010 600 etec renegade wont run properly. Here are the symptoms starts fine idles fine let it warm up for 5 minutes put sled on the stand hold the throttle at 60MPH - runs at 60 for about 5 seconds Drops to 40MPH for 5 seconds Goes up to 80 MPH for about 2 seconds Drops right down to 10...

My boyfriend has a 2010 ski-doo summit everest with a 154" track. I'm looking to get him a cover for it but I'm not as knowledgeable with snowmobiles and what a good cover would be. Where can I find a good quality cover for his snowmobile? TIA

This has probably been gone over plenty of times and I've tried to do as much research as possible but I still have questions. I'm looking into saving up for a new sled I was thinking a 2010 xrs, but being younger these sleds can be a. It pricy for me. I want a sled that I can beat. I jump...

So I have in the garage now a 2010 500ss, it has relatively low miles but so the story from the beginning was bought blown up 4 years ago and was rebuilt, ran good for 1 season and toasted the PTO side, so 3 years ago top end was rebuilt and ran good for a season did the same thing but the MAG...

Hey guys I'm new to the forums so I may need to be referred to another category but anyways , I own a 2010 mxz 800 Xrs and I'm 6'1 an the stock bars and 5.1 riser wasn't enough so I went and purchased a 7inch rsi riser and a set of rsi backcountry bend bars I believe their 3inch rise and then I...

The center skid shock is blown on a 2010 ski doo summit, I am not currently around the sled so I don't know the dimensions of the shock. Would anyone happen to know? Unfortunately I haven't been able to find any info about shock dimensions online. Just one of the many exciting steps to get...

well last 2 times i went to start up the old sled she sounds wrong and will not idle. its a 2010 800r xps, maybe 4000 miles on it changed plugs didnt help only change was last time I was out of oil at the end of the season Spicers was out of semi synth so wifey got me full syth only time i...

Blew a top end in a 2010 800r renegade x, needs a cylinder and a full rebuild, what is the best way to do it, I'm looking for it to be as reliable as possible... How much will parts cost, what are the best parts, where should I order them, and any tips on cleaning power valves!? Thanks guys I...

Looking at a 2010 Renegade X tomorrow night ...sweet looking sled (Red,White,Black Package)Anything in particular that I should be looking for ...sled only has 3000kms on it. It is Clutched ,Fourth Wheel Kit,added. Thanks

Hi all, This is my first post so please forgive me if I've posted my question in the wrong place. I recently purchased my own skidoo (a 2010 1200 4-tec MXZ TNT Adrenaline) and my husband and I are trying to figure out the right settings for the suspension/track/etc. We used to have a 2-up, so...

Hi, I have a 600RS 2010 with 3000km and the flipper is very hard to push. The carbs are clean, the flipper is new and the seld run perfectly. But the lever is very hard.... Does anyone have an idea of the problem or anyone have solved this problem in the past? Thanks

Just installed a new Team secondary on my 2010 Renegade 600 etec. I took it into a local shop to have the clutch aligned since I didn't have the magic tool. They say I over torqued the retaining bolt (over 18 lbs) and the threads are damaged inside the jack shaft. They want to tear it apart and...