Alright. Completely new to snowmobiles. A year or so back I stumbled on a freebie and snapped it up for later. It's a Sep 1996 mfg Skidoo Grand Touring with the Rotax 583. VIN is 1127 00968 and the frame stamp matches the vin tag. Completely there, just left sitting under tarps for a decade...

Having trouble finding the year this 670 Rotax is. Has a bar code ID on it and the recoil is on the outside, so it's 95+. I'm thinking this is out of a 96 MXZ 670, can anyone confirm? Just the engine, this rotax was swapped into another chassis. There is a D stamped on the head. The bar...

So, I just picked up a '96 Grand Touring 580 with low compression for an insignificant amount of money - mostly because of the positive responses from members on various forums. Previous owners have indicated that they felt this sled was solid with a reliable engine. We did a top end on our '84...

Need help diagnosing a problem with my 1996 Ski-doo Grand Touring 670SE. The oil in the reservoir appears to be draining into the crank case when the sled sits over the summer. Looking for tips on diagnosing where the problem is. From what I understand it could be an inner crank seal problem...

Ive been working all winter on a 1996 formula 3 triple. It was burning coolant. Ive replaced all top end gaskets (except for the small spark plug O rings) and ive replaced the water pump that people said was prone to failure and the gear was completely sheered off the shaft of the water pump due...

Hi, this is my first post. i just bought a 1996 formula 3 600. it has great spark but nothing will stop the spark. not the kill switch not the key and not the tether. It will still spark with them all shut off. The guy I got it from said he replaced the stator, I have no clue what I should do to...

The sled is in good condition, runs good! 1996 Mach 1 670 twin with 44mm carbs · Pulled from storage, cleaned carbs added fresh gas and started right up. · Suspension upgraded to a SC III from a 2002 MXZ. · Track in good shape as well. · There...

Hey Everyone, This topic I would like to put out there for anyone with an older Formula sled who is looking to do some weight reduction by removing the old bulky seat and putting on a newer model seat (My seat of choice is off of a 2004 Rev) I bought this seat off of a friend for 80$ and after...

Is anyone a mikuni expert? I need to source a carb (body at least), I have one that the float arm tower physically is busted on...(wish I knew how that happened!) didn't see any on ebay and a quick google search left me in the dark. (not sure if it's mag or PTO side yet, need to get it back...

I am replacing the track on my formula ss and want to swap out the pads at the same time as the brakes are not working very well at all. The fixed side of the bpad is part of the chaincase and when we install the new thick pad it pushes so hard on the rotor, you cannot turn the shaft... My...

Item: welded rear arm Category: Sled Year: 1996 Location: ontario Price: N/A looking for welded rear arm for 1996 grand touring part #503151200 much thanks.

I Have a question. I have a 1996 formula 3 ski doo. I just put 3 new oil injection lines on and one of them has no oil going through it. the other two are fine and all cylinders are getting oil. does that mean my oil pump is dying or what? I Thought there might be something blocking it but is...

I have a 96 Formula Z 583 that is in rough shape but seems to run alright. I picked up a 98 MXZ with no engine for $150 that looks real good and want to swap it over. I know the Form Z is an F series and the mxz is an S series frame but not sure what it will mean for an engine swap. Is it...

I have a 1995 Ski Doo Formula Z 583. All the parts sites microfiche for Ski Doo start at 1996. Does anyone know where pre 1996 diagrams can be found? I need part number for gas shutoff valve, 3 way connector in gas line for connecting primer tube, gas line connector at gas tank and rubber...

hi i have a 1996 mxz 583 im looking to make a can for that is loudor then stock. i aredy know that puting a homemade can on will not change the back presser anuff to change anything as the back presser comes from the tuned pipe wich will not bechanged. also im not worryed about closeing trails...

so i broke my stock seat of my mxz and its in nead of recovering so insteed of rebuliding my seat or buying a new one i thought of buliding one useing 1/2 plywood and some 2x2 and makeing a seat the same size as the stock one but making a big trunk in the middle of the whole seat so there was...

Does anyone know off hand if a Reverse kit purchased originally for a 1996 Summit 500/583 will work on a 1995 Summit 583. I know they changed the chassis, but did they change the drive system?

Hey everyone! I own a 96 Formula S with a 380cc motor. I did some compression testing myself and I don't know what is the best compression. In my right cylinder I got 120psi in my right and 110psi on my left cylinder. I don't think it should be 10psi off? My dad says the fan cooled motors are...