XP cylinder specs? - REV-XP / XS Chassis - Performance Trail 120-129 Inch Models - DOOTalk Forums

Jump to content

 






Photo

XP cylinder specs?


  • Please log in to reply
1 reply to this topic

#1 mfguilbault

mfguilbault

    Newbie

  • Members
  • Pip
  • 1 posts
  • Sled:2010 600 TNT

Posted 19 November 2020 - 08:17 AM

Trying to figure out skidoo cylinder numbers for a rebuild.

Looking for a stock bore size cylinder (useable) for a 2010 SkiDoo 600TNT (carb, non-HO) (500SS motor?)

Part# 420613628

Numbers on the side of the cylinder are 6923-434 Not sure what these numbers mean...?

Are 420613625 cylinders interchangeable?

I’m told there are “early” and “late” 500SS cylinders with the difference being a “decompression slot”?

#2 Daag44

Daag44

    Advanced Member

  • DOOCrew
  • 25704 posts
  • Gender:Male
  • Location:South Shore, Quebec
  • Interests:1973 Olympic
  • Sled:2007 1000 SDI

Posted 21 November 2020 - 08:20 PM

All plating shops know the different cylinder castings. Give one of them a call.


Air/Fuel Ratio for two and four strokes
Air/Fuel Ratio for 1200 with boost
Air/Fuel Ratio is measured through emissions
Wideband and EGT
Wideband readings of Air/Fuel Ratio on a two stroke
600 SDI MY2004 Lean/Hot spot running 6900-7000 rpm @ 40-45% Throttle Opening
800R Cranking Compression
800R Oil Injection / Premix combo
800R Turbo?
850 Cente Oil line for coolant pump melted
850 Main Oil line caught fire #1 and #2
900 ACE Turbo - muffler turning red hot
1200 4-TEC Mapping
1200 4-TEC MY 2009 to 2011 Fuel Line issues that could cause a fire
Batteries
Belt Blowers: Overview of UPMICHIGANDER's experience
BUDS 3.3.0 won't connect to SDI
BUDS not connecting to HO or SDI - Try a CanDoo
CVT efficiency - BlueMax
Deep snow intake for XP chassis
Diagnoses
E-TEC 600HO Clutching
E-TEC Oil Pump
E-TEC Dial-A-Jet
E-TEC Electric Start troubleshooting
E-TEC Engine Management
E-TEC Stator fault codes P1562 or P1563
E-TEC Capacitor Charge Hold Test and Residual Voltage Test
E-TEC Voltage Rectifier Regulator troubleshooting
Fuel Issues: Could new Ester type oxygenated additives be deteriorating the Fuel Sender Grommet?
Fuel pump and regulator replacement for ACE, E-TEC and SDI
Gasoline quality and storage
Bad Gas for a Two Stroke - Is it a Myth ?
G4 Clutch Alignment, Engine Movement, Sheave Runout and Clutching
GNR CVT Alignment for the G4
Grip N Rip Clutch Alignment testing
G4 850 Throttle Jerkiness solved with clutching
G4 850 Snappy throttle/clutch engagement
G4 850 pDrive tech - A question of Engineering
G4 Steering
G4 850 Tuned Pipe @ 12.6 lbs and Muffler @ 15.4 lbs vs 800R and 800RE muffler weight
Pictures - How to resize and upload to DooTalk
Pictures - How to post with the correct orientation
Pipe Pressure testing on a dyno
Pipe Pressure testing from LRD (#1) and (#2)
Pipe Pressure testing results from BRP
Oil versus Fuel consumption
Power Loss - How to diagnose in the field
Power at the Crankshaft vs Track - BlueMax
Power Curves: 600 HOE (E-TEC)
Power Curves: 600 vs 800 vs 850 vs 1000 vs 1200
Power Curves: 1000 vs 800 vs 600
Power curves: 800RE 2010.5 to 2016 vs 2016.5 850
Quebec/NY State border crossing
REV Gen1 Gauge Display stuck on "SCALE"
REV Gen1 Volt and Temp Gauge install
REV Gen1 electrical connectors for sensors and MPEM (Multi Purpose Engine Module)
Seafoam for E-TEC injectors
Shortblock or Rebuild?
Ski-Doo Snowmobile Tech Training
Stator testing for E-TEC using a T harness/Bridge
Stator testing for 1200 4-TEC
Stator replacement for a 1200 4-TEC
Suspension Adjustment
Triples - Coolant Pump Assembly
Y-Pipe bolts loosening fix





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users